Bathroom Vanities

Width 48" | Height 96" | Depth .75"

Back panel that is made of 3/4" thick plywood. Only 1 side will be finished, all edges and opposite side will be unfinished.

Width 38.5" | Height 34.5" | Depth 24"

1 door blind base corner cabinet with 1 drawer and 1 shelf. The actual width is 38 1/2", but must be pulled at least 3 1/2" from the corner, taking up 42" of wall space. It can be pulled a max of 9.5", taking up 48" of wall space. The door width is 15 3/8", the stile width is 9-3/4" and the blind opening width is 12 3/4". A filler must be used between the blind and the adjacent cabinet so the doors and drawers are able to open without interference. The filler must be purchased separately.

Width 42" | Height 12" | Depth .75"

Arched Recessed panel valance that can be trimmed up to 3" on each side.

Width 42" | Height 30" | Depth 21"

Arched wood hood with an overall depth of 21", the depth of the main part of the hood (which goes against the wall) is 15". The top panel will lift up and the sides will be flush. If crown is being installed, it would be installed above the cabinet, not on the face frame. A full interior stainless steel hood liner will also be installed (liner can be removed on site, if needed, however a hood liner is strongly recommended to prevent the wood hood from getting burned and is required by code in many places. The interior hood liner dimensions are as follows:

• Rear width: 40-1/2”
• Front width: 35-7/8”
• Depth of 34-1/2” section: 13-3/4”
• Depth of 29-7/8” section: 4-1/2”
• Max fan size: 40-1/2” x 13-3/4”
• Note that a blower is not included and must be purchased separately

Width 30" | Height 34.5" | Depth 24"

2 door base cabinet with 1 three quarter depth adjustable shelf and 2 drawers. This cabinet will have a 2-5/8" center stile.

Width 42" | Height 34.5" | Depth 24"

Sink base cabinet with 2 doors and 2 false drawer fronts. This cabinet will have no shelves.

Width 42" | Height 34.5" | Depth 21"

Vanity sink and drawer base combo cabinet with (2) 8-3/4" wide doors in the middle, (1) 6-3/4" high false drawer front across the top of the entire cabinet, and (2) 11-1/2" high drawers on the left and right. This cabinet will not have any shelves.

Width 3" | Height 42" | Depth 2.25"

Wall plain pilaster. The filler the pilaster is mounted on is 3/4" deep, the pilaster itself is 1-1/2" deep. Top and bottom sections above and below the pilaster are each 2" tall. 2" will need to be trimmed from the top or bottom before installation. **Pilasters are handmade and may therefore feature inconsistencies in shape or form. These are in no way considered defects**

Width 11.25" | Height 42" | Depth .25"

Wall skin that can be cut to size as needed.

Width 48" | Height 34.5" | Depth 24"

1 door blind base corner cabinet with 1 drawer and 1 shelf. This cabinet can be placed all the way in the corner (without any pull) so it would take up 48" of wall space. It can be pulled a max of 3", taking up 51" of wall space. The door width is 21-1/4", the stile width is 7-3/8" and the blind opening width is 18-3/4". A filler must be used between the blind and the adjacent cabinet so the doors and drawers are able to open without interference. The filler must be purchased separately.

Width 48" | Height 12" | Depth .75"

Arched recessed panel valance that can be trimmed up to 3" on each side.

Width 48" | Height 30" | Depth 21"

Arched wood hood with an overall depth of 21", the depth of the main part of the hood (which goes against the wall) is 15". The top panel will lift up and the sides will be flush. If crown is being installed, it would be installed above the cabinet, not on the face frame. A full interior stainless steel hood liner will also be installed (liner can be removed on site, if needed, however a hood liner is strongly recommended to prevent the wood hood from getting burned and is required by code in many places. The interior hood liner dimensions are as follows:

• Rear width: 46-1/2”
• Front width: 41-7/8”
• Depth of 34-1/2” section: 13-3/4”
• Depth of 29-7/8” section: 4-1/2””
• Max fan size: 46-1/2” x 13-3/4”
• Note that a blower is not included and must be purchased separately